ABSTRACT
The purpose of this study was to evaluate the structural characteristics of the thread length of orthodontic mini-screws and the effects of insertion and removal torques according to the formation of the cutting flute. Two types of mini-screws were made, with a thread length of 6.0 mm and a thread length of 3.3 mm. In order to examine the effect of flute formation, the experiment group was divided into a miniscrew test group with flute formation and an experiment group without flute formation. To evaluate the effect of flute formation, two flutes were formed at 180°on the circumference, and at the tip of the mini screw, up to 4 mm for thread length of 6.0 mm and 2.4 mm for thread length of 3.3 mm. A biomechanical test block formed of 2 mm cortical bone and 10 mm cancellous bone was used to eliminate the influence of the difference in cortical bone thickness and bone density according to the insertion site. 1 mm diameter guide hole was drilled on the test block and the mini-screw was placed vertically. Using a 0.1 N·cm precision digital torque gauge, the maximum torque value was recorded at this time by embedding it to the top of the screw under a static load of 1.2 kg and the value when it was removed in the opposite direction. The insertion torque values for the 6.0 mm and 3.3 mm length mini screws were (29.53±1.84) N·cm and (26.84±2.15) N·cm, and the removal torque values are (14.50±1.37) N·cm and (13.15±2.89) N·cm, respectively.There were no statistically significant differences (P>0.05). The flute of 6.0 mm mini-screws had no statistically significant difference in both insertion and removal torque values and increased to (30.13±1.97) N·cm and (18.65±1.10) N·cm (P>0.05). In experiments with 3.3 mm mini-screws, the insertion and removal torque values decreased to (20.99±3.94) N·cm and (11.32±2.03) N·cm, respectively, showing a statistically significant decrease only in the insertion torque values (P<0.05). The insertion and removal torque values of the mini-screw were not significantly increased even when the screw length was doubled, and the flute formation effect was different with the screw length.
ABSTRACT
The purpose of this study was to evaluate the structural characteristics of the thread length of orthodontic mini-screws and the effects of insertion and removal torques according to the formation of the cutting flute. Two types of mini-screws were made, with a thread length of 6.0 mm and a thread length of 3.3 mm. In order to examine the effect of flute formation, the experiment group was divided into a miniscrew test group with flute formation and an experiment group without flute formation. To evaluate the effect of flute formation, two flutes were formed at 180°on the circumference, and at the tip of the mini screw, up to 4 mm for thread length of 6.0 mm and 2.4 mm for thread length of 3.3 mm. A biomechanical test block formed of 2 mm cortical bone and 10 mm cancellous bone was used to eliminate the influence of the difference in cortical bone thickness and bone density according to the insertion site. 1 mm diameter guide hole was drilled on the test block and the mini-screw was placed vertically. Using a 0.1 N·cm precision digital torque gauge, the maximum torque value was recorded at this time by embedding it to the top of the screw under a static load of 1.2 kg and the value when it was removed in the opposite direction. The insertion torque values for the 6.0 mm and 3.3 mm length mini screws were (29.53±1.84) N·cm and (26.84±2.15) N·cm, and the removal torque values are (14.50±1.37) N·cm and (13.15±2.89) N·cm, respectively.There were no statistically significant differences (P>0.05). The flute of 6.0 mm mini-screws had no statistically significant difference in both insertion and removal torque values and increased to (30.13±1.97) N·cm and (18.65±1.10) N·cm (P>0.05). In experiments with 3.3 mm mini-screws, the insertion and removal torque values decreased to (20.99±3.94) N·cm and (11.32±2.03) N·cm, respectively, showing a statistically significant decrease only in the insertion torque values (P<0.05). The insertion and removal torque values of the mini-screw were not significantly increased even when the screw length was doubled, and the flute formation effect was different with the screw length.
ABSTRACT
The purpose of this study was to evaluate the effect of the reaction between investment material and zirconia on the strength of zirconia in the application of heat-pressing method. Sixty specimens were cut (24 mm×4 mm×0.5 mm) into plates from Zirtooth ™ Multi O-9814 block (∅98×14T, HASS, Gangwondo, Korea) and sintered at 1450℃. Specimens were divided into 6 subgroups according to the depending on the investement material; (a) UN group (Control), (b) PH group (Prime vest HS), (c) CP group (Calibra-press), (d) BV group (BC-Vest), (e) MH group (Microstar-HS), (f) F1 group (Formula 1). Five investment materials were buried according to the procedure recommended by the manufacturer and left at room temperature for 30 minutes. The investment mold was dried and maintained at an elevated temperature of 850℃ for 50 minutes. Then, Amber Lisi-POZ LT (HASS) was placed in a thermoformed electric furnace (Programat EP3000/G2, Ivoclar Vivadent, Schaan, Liechtenstein) together with the mold, heated to 915℃ at an elevation temperature of 45℃/min, and moored for 15 minutes. The specimens were loaded to fracture in a universal testing machine and the fracture surface was examined by a field-emission scanning electron microscopy (FE-SEM). The surface of the zirconia specimen with the investment material was analyzed by energy dispersive X-ray spectroscopy (EDS). The 3-point flexural strength test showed the highest value (1265.5 MPa) in the UN group and the lowest value (756.1 MPa) in the F1 group. As a result of EDS analysis, the largest amount of Si was detected in the F1 group, and the most interfacial changes occurred as a result of FE-SEM analysis. It was concluded that when the zirconia is buried with the investment material and the heat press molding is performed, the state of the interface is changed due to the investment material at the bonding interface while the strength is lowered.
ABSTRACT
The purpose of this study was to evaluate the effect of the reaction between investment material and zirconia on the strength of zirconia in the application of heat-pressing method. Sixty specimens were cut (24 mm×4 mm×0.5 mm) into plates from Zirtooth ™ Multi O-9814 block (∅98×14T, HASS, Gangwondo, Korea) and sintered at 1450℃. Specimens were divided into 6 subgroups according to the depending on the investement material; (a) UN group (Control), (b) PH group (Prime vest HS), (c) CP group (Calibra-press), (d) BV group (BC-Vest), (e) MH group (Microstar-HS), (f) F1 group (Formula 1). Five investment materials were buried according to the procedure recommended by the manufacturer and left at room temperature for 30 minutes. The investment mold was dried and maintained at an elevated temperature of 850℃ for 50 minutes. Then, Amber Lisi-POZ LT (HASS) was placed in a thermoformed electric furnace (Programat EP3000/G2, Ivoclar Vivadent, Schaan, Liechtenstein) together with the mold, heated to 915℃ at an elevation temperature of 45℃/min, and moored for 15 minutes. The specimens were loaded to fracture in a universal testing machine and the fracture surface was examined by a field-emission scanning electron microscopy (FE-SEM). The surface of the zirconia specimen with the investment material was analyzed by energy dispersive X-ray spectroscopy (EDS). The 3-point flexural strength test showed the highest value (1265.5 MPa) in the UN group and the lowest value (756.1 MPa) in the F1 group. As a result of EDS analysis, the largest amount of Si was detected in the F1 group, and the most interfacial changes occurred as a result of FE-SEM analysis. It was concluded that when the zirconia is buried with the investment material and the heat press molding is performed, the state of the interface is changed due to the investment material at the bonding interface while the strength is lowered.
ABSTRACT
BACKGROUND: Plate fixation is the most commonly used technique for the treatment of shaft fractures of both forearm bones (SFBFBs). However, all fractures are difficult to treat with plate fixation because of soft tissue injuries, fracture patterns, or the patient's condition. The purpose of this study is to compare the functional results of plate fixation only and combined plate and intramedullary (IM) nail fixation in SFBFBs. METHODS: Fifty-nine cases of SFBFBs that were surgically treated from June 2007 to July 2012 were retrospectively reviewed. In this study, 47 cases that were followed up for more than 12 months were included. All SFBFBs were divided into two groups according to the methods used for internal fixation: plate fixation only (group A) and combined plate and IM nail fixation (group B). The fixation methods were determined intraoperatively. Plate fixation was considered as the first option in all cases, but combined plate and IM nail fixation was selected as the second option if it was difficult to be fixed with plate only. Groups A and B comprised of 31 and 16 cases, respectively. The functional results were evaluated by the Grace and Eversmann rating system and the Disabilities of the Arm, Shoulder and Hand (DASH) questionnaire. RESULTS: In groups A and B, a radiologic union was achieved in 30/31 and 14/16 cases and average union time was 11.1 and 17.8 weeks, respectively. According to the Grace and Eversmann rating system, group A had excellent results in 15 cases, good in 14, acceptable in one, and unacceptable in one. Group B had excellent results in three cases, good in nine, acceptable in two, and unacceptable in two. The average DASH score was 7.1 points (range, 0 to 19.2 points) in group A and 15.1 points (range, 0 to 29.6 points) in group B. Three cases of nonunion with unacceptable results achieved a bony union by additional procedures and the functional results of these cases improved to good or excellent. CONCLUSIONS: The functional results and the average union time were superior in group A than in group B. However, we think that combined fixation is a useful method for SFBFBs that cannot be treated with plate fixation only.